http://www.eu.onkyo.com/en/irajax/en/articles/firmware-update-tx-nr676e-139951.html/cHJvamVjdC5jb21tb24udXJsU2hvcnRlbmVyOw==

Firmware Update TX-NR676E

We are pleased to offer this firmware update for the best possible performance of your AV Receiver.

TX-NR676E
(Version 1060-8010-2040-0008)

  • Improve the noise during playback via USB/Network

To check if your firmware is the latest version, go in to Setup -> Hardware Setup -> Firmware Update and check the version number. If any of the numbers differ from the latest version available, please update your unit.

Update via USB storage 

Note: Please remove the wired/wireless connection before updating through USB.
Please prepare a USB storage device such as a USB flash memory stick. You need at least 128 MB of available space to update the firmware. Please unpack the ZIP file onto an empty USB Stick which has been formatted with the FAT file system. 
We hope you enjoy the improved functionality this update provides to your AV Receiver.

Precautions for the Firmware Update

Please read the update instructions carefully before beginning.
The firmware update should take 30 to 40 minutes. Once the update begins, don't turn off the power supply to the A/V receiver until it is time to restart it.
Depending on the conditions of the network, a firmware update via a network may take more than one hour or even fail to finish. If the update is not completed within two hours, turn off the power supply by pushing the ON/STANDBY button and then try updating again from the beginning.
Updating the firmware and adjusting the settings will be done automatically, but may take some time to complete. Please follow the procedures as instructed when you update. Note that the update may fail, or cause problems for your A/V receiver, if you do any of the following:

  • Pull out the A/V receiver’s power cord;
  • Interrupt the power supply to the A/V receiver (e.g. if the breaker is tripped or if there is an electrical outage);
  • Insert or remove the LAN cable from a device in your network when updating over a network;
  • Insert or remove a USB memory device from the A/V receiver when updating via USB;
  • Operate components connected to the A/V receiver via HDMI, such as a TV or a recording device.
If your A/V receiver is damaged for any of the reasons above, an Onkyo service center will repair the unit for a fee.

If you see "No Update" on the front panel immediately after you have started the firmware update process, you have the latest firmware. In this case it is not necessary to do this update.

Downloads

Firmware

RSS News

State-of-the-Art Onkyo RZ Series Receivers Open New Entertainment Horizons with Expansive 9.2-Ch Surround-Sound, 4K HDR Video, and Wireless Multi-room Audio

Imagine your cinema-room filled with flawless sound that flows from all directions, and the big screen lit up with 4K HDR… more

Press Release dated: 15 May 2018
Meet the 7.2-Channel TX-NR686 from Onkyo, a New Benchmark in Value Delivering Captivating 3D Movie Sound and Seamless Multi-Room Audio Entertainment

Onkyo bundles Dynamic Audio Amplification with cutting-edge wireless multi-room audio technologies, 4K video support, and 3D… more

Press Release dated: 6 Mar 2018
Pioneer & Onkyo Europe GmbH makes its MWC 2018 debut, exhibits innovative AI-based products

Onkyo Corporation announces that it will exhibit a number of AI-based products and technologies at MWC (Mobile World… more

Press Release dated: 26 Feb 2018
15th Onkyo International Braille Essay Contest

Audiovisual manufacturer Onkyo Corporation, Japan Institute of Scientific Research for Education, and the Braille Mainichi… more

Press Release dated: 29 Dec 2017
Pioneer & Onkyo Europe GmbH debuts new FlareConnect™ Wireless Multi-room Audio Distribution system

Pioneer & Onkyo Europe GmbH is pleased to announce FlareConnect™, its next generation, in-house developed wireless… more

Press Release dated: 26 Oct 2017

Current Catalogue

Catalog ONKYO Audio Video Products 2017-2018
Download pdf (51.54 MB)